What're your beliefs on A Step-by-Step Guide to Installing a Bathtub?
Installing a bathtub isn't precisely rocket science, yet it does need strong plumbing, carpentry, and also in some cases, tiling skills. Changing an old tub with a brand-new one is additionally a reasonably tough task. If the old tub is readily accessible, the job can move quickly; if you have to open a wall to remove the old tub and place the new bath tub, the job is much harder. In either instance, the job is within a house handyman's abilities, although you will certainly need an assistant to vacate the old bathtub as well as set in the new one. Ensure you have actually certified on your own for the job as well as are comfortable attempting it. Rather than working with a service provider to take over a halfway-completed task, it is much better to think about using one prior to you begin. Chances are you might need an expert plumber to make tube connections.
This post will assist you set up a new tub in your washroom if you have actually already acquired a new bathtub and do not require to change the arrangement of your previous water supply pipelines.
Your tools as well as material list ought to consist of the following:
Getting ready for the Setup
To start with, the sustaining frame supplied with the bath needs to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the tap features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to prevent strain on the tub.
Fit the adaptable tap connectors to the bottom of the two faucets using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you utilize all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is separate the water supply. After doing so, activate the faucets to drain any water staying in the system. The process of getting rid of the existing faucets can be rather troublesome because of the restricted access that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the remaining water that will certainly come from the pipes. Once the supply pipes have been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Before carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bathtub in the required placement. The wood boards are useful in equally spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four little points.
The next objective is to make sure that the tub is leveled all round. This can be attained by examining the spirit level as well as changing the feet on the bath tub till the level checks out degree.
To set up faucets, fit all-time low of the furthest flexible tap port to the ideal supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Activate the water supply and also inspect all joints and brand-new pipework for leaks and tighten them if necessary. Fill up the tub as well as additionally inspect the overflow outlet and also the regular electrical outlet for leaks.
Ultimately, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and sealing around the bath tub must wait up until the tub has been used at least once as this will certainly resolve it right into its last placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in place with the supplier given backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former type must be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can move enough to split a rigid seal, creating the water to permeate the wall surface in between the bath as well as the tiling, bring about complications with moisture and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and installations. They are marketed in tubes and cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched paper or soft rope. Bear in mind to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in usage. The sealer can fracture fairly early if you do not consider this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly readily available on the market. It is recommended to fit the floor tiles utilizing water-resistant or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very involved in Installing A Bathtub and I am praying you liked the post. Do you know about someone else who is enthusiastic about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Feel free to promote it. I enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Expertise at your service.